- Tire Changers
- Wheel Balancers
- Car Rotisserie
- Shop Equipment
- Weaver Wear
Warehouse pick up price Now ($1699.00). The Weaver® Lift W-9D excels as a fully featured 9,000-lb. capacity auto lift complete with Super-Symmetric arms that allow asymmetric or symmetric loading, single point safety release, commercial grade arm restraint locks and dual direct-drive cylinders. The W-9D is now priced hundreds below comparable models and about the same as chain driven models with less features. Also Included FREE for a limited time, a set of 4 U-Shaped Frame Adapters!
Free Shipping To Over 85% of the USA - See Where It's Free
For warehouse pick up at our Texas Warehouse or North Carolina Warehouse call for pick up price ($1699.00), make payment and schedule a pick up appointment.
Experience the power and reliability of direct-drive at the price of chain drive with frame adapters included!
What is Super-Symmetric and how does it load either asymmetric or symmetric? This unique arm style utilizes 3-stage front arms and typical 2-stage rear arms. The 3-stage front arms allow asymmetric loading when the front arms are near fully retracted and symmetric loading when the front arms are near fully extended. Short enough for wide unibodys yet long enough to reach the frame on framed vehicles.
This commercial grade 2-Post Lift also has dual height positions that allow for installation under a 12' ceiling or a second selection to raise the height to 12' 6". Stack pad height adapters ( 1 1/2", 3" and 6") are also included to adjust pad heights for various vehicles including trucks. Also included is a set of 4 Frame Adapters that are typically sold as optional equipment from other brands.
The W-9D is an overhead beam style clear-floor design with a padded shut-off bar for overhead vehicle protection. The columns are positioned symmetric (straight) with Super-Symmteric arms that allow the most flexibility for loading either asymmetric or symmetric lifting points.
States Derek Weaver, "Quality, Durability and Affordability or it wouldn't wear the Weaver® Lift label. This is an extreme value when compared to the prices some companies want to charge. Get more here and Get It Up".
5-year structural warranty, 1-year hydraulic cylinder and 1-year warranty on power unit. Affordably priced for the commercial shop or enthusiast garage.
Showing reviews 1-10 of 24 | Next
Posted by Chuck Forsyth on 2nd Oct 2017
Pretty excited to have a car lift finally. I did quite a lot of research and came upon the W-9D lift from Weaver. Just lifted my first automobile and it worked just fine. Like the rest of the reviews the instructions were terrible. Someone should take a little time and come up with better ones. That said if you are reasonably mechanical you can figure it out. I had a few questions and got very quick responses and got it done. Dan was very helpful.Seems to be built well. Only time will tell. Thanks
Posted by TIM HAYALI on 23rd Jan 2017
This is the fourth weaver lift I have has installed. I haven't had a problem yet with any of them.
Posted by John Basham on 22nd Nov 2016
I have been wanting a lift for a long time. I done a lot of research on which one to buy. I am so glad that I chose the W9D. I love it. It was easy to assemble and it works GREAT!!!!!!!! If you are looking for a great lift for a unbelievable price look no further. The only regret I have is that I didn't buy it sooner. Thanks Derek Weaver for a great product at a affordable price.
Posted by Jake Daigle on 8th Jun 2016
Just finished installing my lift. Haven't had a chance to run it with a load yet, but it works well without one and looks great!
My only complaint would be the instructions. Finding the correct bolts to use for each part was a pain by having to flip back and forth trying to match part numbers with bolt sizes in metric. Also it is hard to tell by the pictures which way parts needed to face and which sides they needed to be mounted to. The poor instructions isn't that big of a deal as far as I'm concerned. Just plan for a few extra hours on the install time.
After having a hand standing the two posts up, I finished installing the rest of the lift myself. I recommend leaving the bolts to the upper assembly and extension loose and use a jack to level the top beam going across before tightening. I ended up having to go back and do this because the cables will rub if the top beam isn't level.
I would recommend this lift & would purchase it again for sure!
Posted by Mark Vaught on 24th Mar 2016
I bought this lift a couple of months ago for my hobby shop at my home. I researched several different brands and models and ultimately decided on this lift because of the direct hydraulic drive rather than the chain drive systems common in lifts of this size.
I picked up the lift with my 5x10 utility trailer at the shipping terminal, where they could load it for me with their forklift. Once home, I unloaded it one piece at a time with the aid of my engine hoist (cherry picker). It wasn't optimal, but I was able to get it all on the floor in this manner.
I cleaned the parts with WD-40 and assembled them according to the instructions. The instructions were somewhat vague and unclear as others have mentioned, but the most difficult part was trying to ensure I was using the correct fastener for the correct part. It's just a minor nuisance.
Once assembled, I used the engine hoist to lift each of the side posts up to a point where I could get under them and walk them up by myself. This was tricky, and I do NOT recommend trying to assemble this lift by yourself.
I measured, marked, measured again, and marked again where the side posts should be permanently installed and proceeded to drill the holes. Word of advice: use a BIG drill. It took me HOURS to get my holes drilled because my drill wasn't big enough. I should have probably used two bits also, because mine was extremely dull toward the end. I used a shop vac and compressed air to blow the holes out during drilling and before installing the wedge bolts.
Electrical hookups were straightforward, as was motor installation and hydraulic lines. I had to tighten one connection after the initial run, but that was it. It's better to check for leaks and have to tighten them later than to get them too tight to begin with.
I've used it for a few months now and I've had zero problems with the lift. I've lifted two Mustangs, a Ford Ranger extended cab, and a GMC Acadia with no problems. Make sure you know good lift points with whatever vehicle you're lifting.
I'm glad I purchased this lift and would recommend it to anyone not needing to lift heavier vehicles.
Posted by Jared on 13th Sep 2015
I've been wanting a lift for a long time. I purchased this lift over a year ago. I have used this lift practically every weekend and haven't had any issues. Lifts all my vehicles with no problem(up to a full sized truck). I installed the lift with help from my dad. Was a simple afternoon project.
I would recommend this lift, great value for the price.
Posted by Frankie on 27th Jul 2015
I have done research on lifts for my home garage for about 2 years. This product is great for the price. I really wanted a rotary asymmetric lift but could not see myself spending 3800 for a lift for my home. I am glad I went with this lift it is wide enough to open car door and get out even though it is not asymmetric posts. Good quality just as good as any other china made lift as a direct lift or such and less money. Directions are pretty bad but was able to figure it out without making any calls. I received this lift in 2 days to NY much faster then I had expected. Carol was very nice and respectful. All in all I am very happy with my purchase and would recommend this lift to anyone looking for a lift like this. Thank you for making my dream of having a lift at home come true.
Posted by John Murray on 13th May 2015
Greaqt product. Very solid and easy to use. Could use some work on the installation instructions, but I'm probably picky as I used to approve aircraft assembly instructions. I wold recommend this product to all you 'garage' mechanics; don't wait like I did. Money well spent!
Posted by Unknown on 29th Dec 2014
I'm very happy with this lift. I had a shop build with this lift in mind with 12' clearance and it fits perfectly.
They were very helpful on the phone during ordering, pickup,and installation. I did the install myself with a few ratchet straps. Don't let it scare you.
The manual was clear except for the component description, could be a little clearer. A great price for a great product!
Posted by ken wagg on 27th Oct 2014
Some of the family said I was crazy to get a lift at 64 but now they want to use it. This lift is unreal. They answered all my questons and helped with everything. Me and my brother put it up in 2 short days. Should have got it 20 yrs ago....Thanks a lot K Wagg
Showing reviews 1-10 of 24 | Next